Can DPAK be used in a through hole pcb if desperate?












2














I purchased the wrong component, have no time to order another one. Best way to go about doing this on a PCB with the plated holes?



https://www.mouser.com/ProductDetail/vishay/irfr9214pbf/?qs=iXwvDCb7I7hjm2Ycf0pGIQ%3d%3d&countrycode=US&currencycode=USD



I have a very small heat sink that is slightly larger than the size of the chip, it came with my Raspberry Pi as a heat sink for the baby sized chip on it.



The backside of the chip is the drain, left pin front-side is gate, right pin source.



enter image description here



Schematic:
enter image description here



The circuit is a pulse generation controller that drives an ultrasonic transducer with 100ns pulses, at a sending rate of about 200-800Hz. The energy in each pulse is very low. Cadence simulates the circuit as I'd expect, can post waves graphs if requested. The BJTs do a good job of controlling the current flow for the desired amount of time, don't get spooked because of the high voltage going through the transformer :^) The zener diode avalanches at 220V, and the power mosfet is rated for 250V.










share|improve this question
























  • How much power does the transistor have to dissipate?
    – mkeith
    Nov 29 at 5:01










  • What is your required power dissipation?
    – Spehro Pefhany
    Nov 29 at 5:01










  • " Power dissipation levels up to 1.5 W are possible in typical surface mount applications."
    – snowg
    Nov 29 at 5:02










  • You can certainly solder it onto that PCB, but the power dissipation capability will be reduced. Normally a DPAK relies on thermal transfer to the large copper pad. But that is a big package, and if you put the heatsink on the front of it, it can probably dissipate a Watt indefinitely without self-destructing.
    – mkeith
    Nov 29 at 5:02






  • 4




    You are quoting from the transistor datasheet. But that is not what Spehro and I are asking. We want to know how much it WILL dissipate based on the circuit you are building. What does the circuit do? Do you have a schematic?
    – mkeith
    Nov 29 at 5:04
















2














I purchased the wrong component, have no time to order another one. Best way to go about doing this on a PCB with the plated holes?



https://www.mouser.com/ProductDetail/vishay/irfr9214pbf/?qs=iXwvDCb7I7hjm2Ycf0pGIQ%3d%3d&countrycode=US&currencycode=USD



I have a very small heat sink that is slightly larger than the size of the chip, it came with my Raspberry Pi as a heat sink for the baby sized chip on it.



The backside of the chip is the drain, left pin front-side is gate, right pin source.



enter image description here



Schematic:
enter image description here



The circuit is a pulse generation controller that drives an ultrasonic transducer with 100ns pulses, at a sending rate of about 200-800Hz. The energy in each pulse is very low. Cadence simulates the circuit as I'd expect, can post waves graphs if requested. The BJTs do a good job of controlling the current flow for the desired amount of time, don't get spooked because of the high voltage going through the transformer :^) The zener diode avalanches at 220V, and the power mosfet is rated for 250V.










share|improve this question
























  • How much power does the transistor have to dissipate?
    – mkeith
    Nov 29 at 5:01










  • What is your required power dissipation?
    – Spehro Pefhany
    Nov 29 at 5:01










  • " Power dissipation levels up to 1.5 W are possible in typical surface mount applications."
    – snowg
    Nov 29 at 5:02










  • You can certainly solder it onto that PCB, but the power dissipation capability will be reduced. Normally a DPAK relies on thermal transfer to the large copper pad. But that is a big package, and if you put the heatsink on the front of it, it can probably dissipate a Watt indefinitely without self-destructing.
    – mkeith
    Nov 29 at 5:02






  • 4




    You are quoting from the transistor datasheet. But that is not what Spehro and I are asking. We want to know how much it WILL dissipate based on the circuit you are building. What does the circuit do? Do you have a schematic?
    – mkeith
    Nov 29 at 5:04














2












2








2


1





I purchased the wrong component, have no time to order another one. Best way to go about doing this on a PCB with the plated holes?



https://www.mouser.com/ProductDetail/vishay/irfr9214pbf/?qs=iXwvDCb7I7hjm2Ycf0pGIQ%3d%3d&countrycode=US&currencycode=USD



I have a very small heat sink that is slightly larger than the size of the chip, it came with my Raspberry Pi as a heat sink for the baby sized chip on it.



The backside of the chip is the drain, left pin front-side is gate, right pin source.



enter image description here



Schematic:
enter image description here



The circuit is a pulse generation controller that drives an ultrasonic transducer with 100ns pulses, at a sending rate of about 200-800Hz. The energy in each pulse is very low. Cadence simulates the circuit as I'd expect, can post waves graphs if requested. The BJTs do a good job of controlling the current flow for the desired amount of time, don't get spooked because of the high voltage going through the transformer :^) The zener diode avalanches at 220V, and the power mosfet is rated for 250V.










share|improve this question















I purchased the wrong component, have no time to order another one. Best way to go about doing this on a PCB with the plated holes?



https://www.mouser.com/ProductDetail/vishay/irfr9214pbf/?qs=iXwvDCb7I7hjm2Ycf0pGIQ%3d%3d&countrycode=US&currencycode=USD



I have a very small heat sink that is slightly larger than the size of the chip, it came with my Raspberry Pi as a heat sink for the baby sized chip on it.



The backside of the chip is the drain, left pin front-side is gate, right pin source.



enter image description here



Schematic:
enter image description here



The circuit is a pulse generation controller that drives an ultrasonic transducer with 100ns pulses, at a sending rate of about 200-800Hz. The energy in each pulse is very low. Cadence simulates the circuit as I'd expect, can post waves graphs if requested. The BJTs do a good job of controlling the current flow for the desired amount of time, don't get spooked because of the high voltage going through the transformer :^) The zener diode avalanches at 220V, and the power mosfet is rated for 250V.







soldering






share|improve this question















share|improve this question













share|improve this question




share|improve this question








edited Nov 29 at 5:09

























asked Nov 29 at 4:54









snowg

827




827












  • How much power does the transistor have to dissipate?
    – mkeith
    Nov 29 at 5:01










  • What is your required power dissipation?
    – Spehro Pefhany
    Nov 29 at 5:01










  • " Power dissipation levels up to 1.5 W are possible in typical surface mount applications."
    – snowg
    Nov 29 at 5:02










  • You can certainly solder it onto that PCB, but the power dissipation capability will be reduced. Normally a DPAK relies on thermal transfer to the large copper pad. But that is a big package, and if you put the heatsink on the front of it, it can probably dissipate a Watt indefinitely without self-destructing.
    – mkeith
    Nov 29 at 5:02






  • 4




    You are quoting from the transistor datasheet. But that is not what Spehro and I are asking. We want to know how much it WILL dissipate based on the circuit you are building. What does the circuit do? Do you have a schematic?
    – mkeith
    Nov 29 at 5:04


















  • How much power does the transistor have to dissipate?
    – mkeith
    Nov 29 at 5:01










  • What is your required power dissipation?
    – Spehro Pefhany
    Nov 29 at 5:01










  • " Power dissipation levels up to 1.5 W are possible in typical surface mount applications."
    – snowg
    Nov 29 at 5:02










  • You can certainly solder it onto that PCB, but the power dissipation capability will be reduced. Normally a DPAK relies on thermal transfer to the large copper pad. But that is a big package, and if you put the heatsink on the front of it, it can probably dissipate a Watt indefinitely without self-destructing.
    – mkeith
    Nov 29 at 5:02






  • 4




    You are quoting from the transistor datasheet. But that is not what Spehro and I are asking. We want to know how much it WILL dissipate based on the circuit you are building. What does the circuit do? Do you have a schematic?
    – mkeith
    Nov 29 at 5:04
















How much power does the transistor have to dissipate?
– mkeith
Nov 29 at 5:01




How much power does the transistor have to dissipate?
– mkeith
Nov 29 at 5:01












What is your required power dissipation?
– Spehro Pefhany
Nov 29 at 5:01




What is your required power dissipation?
– Spehro Pefhany
Nov 29 at 5:01












" Power dissipation levels up to 1.5 W are possible in typical surface mount applications."
– snowg
Nov 29 at 5:02




" Power dissipation levels up to 1.5 W are possible in typical surface mount applications."
– snowg
Nov 29 at 5:02












You can certainly solder it onto that PCB, but the power dissipation capability will be reduced. Normally a DPAK relies on thermal transfer to the large copper pad. But that is a big package, and if you put the heatsink on the front of it, it can probably dissipate a Watt indefinitely without self-destructing.
– mkeith
Nov 29 at 5:02




You can certainly solder it onto that PCB, but the power dissipation capability will be reduced. Normally a DPAK relies on thermal transfer to the large copper pad. But that is a big package, and if you put the heatsink on the front of it, it can probably dissipate a Watt indefinitely without self-destructing.
– mkeith
Nov 29 at 5:02




4




4




You are quoting from the transistor datasheet. But that is not what Spehro and I are asking. We want to know how much it WILL dissipate based on the circuit you are building. What does the circuit do? Do you have a schematic?
– mkeith
Nov 29 at 5:04




You are quoting from the transistor datasheet. But that is not what Spehro and I are asking. We want to know how much it WILL dissipate based on the circuit you are building. What does the circuit do? Do you have a schematic?
– mkeith
Nov 29 at 5:04










2 Answers
2






active

oldest

votes


















4














When doing hand assembly you have a lot of options that aren't practical in production.



you could surface-mount it on that matrix board - if it gets too hot solder thick copper wires into the holes under the the drain pad to act as a heatsink. solder conducts heat better than any affordable non-metallic interface material.
or you could plan ahead and lay down some copper sheet under the drain pad when mounting it and extend the other tabs to reach the circuit board.



A DPAK is basically the same as a TO220 with the leads bent and bits cut off, you could solder pins onto it (that middle tab connects to the drain pad just like in a TO220) and use it through-hole, and optionally solder or clamp a heatsink to the drain pad.






share|improve this answer































    3














    The easiest thing to do is to grab some copper clad pcb and make a quick smd to dip adapter board. You don't need to etch it, for an IC as big as a dpak you can just cut groves on the pcb using a dremel cutting wheel or drill bit. And use wire or a standard 0.1" header to connect it to the pcb you have there.



    This, but bigger
    enter image description here






    share|improve this answer





















      Your Answer





      StackExchange.ifUsing("editor", function () {
      return StackExchange.using("mathjaxEditing", function () {
      StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
      StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
      });
      });
      }, "mathjax-editing");

      StackExchange.ifUsing("editor", function () {
      return StackExchange.using("schematics", function () {
      StackExchange.schematics.init();
      });
      }, "cicuitlab");

      StackExchange.ready(function() {
      var channelOptions = {
      tags: "".split(" "),
      id: "135"
      };
      initTagRenderer("".split(" "), "".split(" "), channelOptions);

      StackExchange.using("externalEditor", function() {
      // Have to fire editor after snippets, if snippets enabled
      if (StackExchange.settings.snippets.snippetsEnabled) {
      StackExchange.using("snippets", function() {
      createEditor();
      });
      }
      else {
      createEditor();
      }
      });

      function createEditor() {
      StackExchange.prepareEditor({
      heartbeatType: 'answer',
      autoActivateHeartbeat: false,
      convertImagesToLinks: false,
      noModals: true,
      showLowRepImageUploadWarning: true,
      reputationToPostImages: null,
      bindNavPrevention: true,
      postfix: "",
      imageUploader: {
      brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
      contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
      allowUrls: true
      },
      onDemand: true,
      discardSelector: ".discard-answer"
      ,immediatelyShowMarkdownHelp:true
      });


      }
      });














      draft saved

      draft discarded


















      StackExchange.ready(
      function () {
      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f409478%2fcan-dpak-be-used-in-a-through-hole-pcb-if-desperate%23new-answer', 'question_page');
      }
      );

      Post as a guest















      Required, but never shown

























      2 Answers
      2






      active

      oldest

      votes








      2 Answers
      2






      active

      oldest

      votes









      active

      oldest

      votes






      active

      oldest

      votes









      4














      When doing hand assembly you have a lot of options that aren't practical in production.



      you could surface-mount it on that matrix board - if it gets too hot solder thick copper wires into the holes under the the drain pad to act as a heatsink. solder conducts heat better than any affordable non-metallic interface material.
      or you could plan ahead and lay down some copper sheet under the drain pad when mounting it and extend the other tabs to reach the circuit board.



      A DPAK is basically the same as a TO220 with the leads bent and bits cut off, you could solder pins onto it (that middle tab connects to the drain pad just like in a TO220) and use it through-hole, and optionally solder or clamp a heatsink to the drain pad.






      share|improve this answer




























        4














        When doing hand assembly you have a lot of options that aren't practical in production.



        you could surface-mount it on that matrix board - if it gets too hot solder thick copper wires into the holes under the the drain pad to act as a heatsink. solder conducts heat better than any affordable non-metallic interface material.
        or you could plan ahead and lay down some copper sheet under the drain pad when mounting it and extend the other tabs to reach the circuit board.



        A DPAK is basically the same as a TO220 with the leads bent and bits cut off, you could solder pins onto it (that middle tab connects to the drain pad just like in a TO220) and use it through-hole, and optionally solder or clamp a heatsink to the drain pad.






        share|improve this answer


























          4












          4








          4






          When doing hand assembly you have a lot of options that aren't practical in production.



          you could surface-mount it on that matrix board - if it gets too hot solder thick copper wires into the holes under the the drain pad to act as a heatsink. solder conducts heat better than any affordable non-metallic interface material.
          or you could plan ahead and lay down some copper sheet under the drain pad when mounting it and extend the other tabs to reach the circuit board.



          A DPAK is basically the same as a TO220 with the leads bent and bits cut off, you could solder pins onto it (that middle tab connects to the drain pad just like in a TO220) and use it through-hole, and optionally solder or clamp a heatsink to the drain pad.






          share|improve this answer














          When doing hand assembly you have a lot of options that aren't practical in production.



          you could surface-mount it on that matrix board - if it gets too hot solder thick copper wires into the holes under the the drain pad to act as a heatsink. solder conducts heat better than any affordable non-metallic interface material.
          or you could plan ahead and lay down some copper sheet under the drain pad when mounting it and extend the other tabs to reach the circuit board.



          A DPAK is basically the same as a TO220 with the leads bent and bits cut off, you could solder pins onto it (that middle tab connects to the drain pad just like in a TO220) and use it through-hole, and optionally solder or clamp a heatsink to the drain pad.







          share|improve this answer














          share|improve this answer



          share|improve this answer








          edited Nov 29 at 7:04

























          answered Nov 29 at 5:41









          Jasen

          9,8701428




          9,8701428

























              3














              The easiest thing to do is to grab some copper clad pcb and make a quick smd to dip adapter board. You don't need to etch it, for an IC as big as a dpak you can just cut groves on the pcb using a dremel cutting wheel or drill bit. And use wire or a standard 0.1" header to connect it to the pcb you have there.



              This, but bigger
              enter image description here






              share|improve this answer


























                3














                The easiest thing to do is to grab some copper clad pcb and make a quick smd to dip adapter board. You don't need to etch it, for an IC as big as a dpak you can just cut groves on the pcb using a dremel cutting wheel or drill bit. And use wire or a standard 0.1" header to connect it to the pcb you have there.



                This, but bigger
                enter image description here






                share|improve this answer
























                  3












                  3








                  3






                  The easiest thing to do is to grab some copper clad pcb and make a quick smd to dip adapter board. You don't need to etch it, for an IC as big as a dpak you can just cut groves on the pcb using a dremel cutting wheel or drill bit. And use wire or a standard 0.1" header to connect it to the pcb you have there.



                  This, but bigger
                  enter image description here






                  share|improve this answer












                  The easiest thing to do is to grab some copper clad pcb and make a quick smd to dip adapter board. You don't need to etch it, for an IC as big as a dpak you can just cut groves on the pcb using a dremel cutting wheel or drill bit. And use wire or a standard 0.1" header to connect it to the pcb you have there.



                  This, but bigger
                  enter image description here







                  share|improve this answer












                  share|improve this answer



                  share|improve this answer










                  answered Nov 29 at 7:57









                  Passerby

                  56.7k453147




                  56.7k453147






























                      draft saved

                      draft discarded




















































                      Thanks for contributing an answer to Electrical Engineering Stack Exchange!


                      • Please be sure to answer the question. Provide details and share your research!

                      But avoid



                      • Asking for help, clarification, or responding to other answers.

                      • Making statements based on opinion; back them up with references or personal experience.


                      Use MathJax to format equations. MathJax reference.


                      To learn more, see our tips on writing great answers.





                      Some of your past answers have not been well-received, and you're in danger of being blocked from answering.


                      Please pay close attention to the following guidance:


                      • Please be sure to answer the question. Provide details and share your research!

                      But avoid



                      • Asking for help, clarification, or responding to other answers.

                      • Making statements based on opinion; back them up with references or personal experience.


                      To learn more, see our tips on writing great answers.




                      draft saved


                      draft discarded














                      StackExchange.ready(
                      function () {
                      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f409478%2fcan-dpak-be-used-in-a-through-hole-pcb-if-desperate%23new-answer', 'question_page');
                      }
                      );

                      Post as a guest















                      Required, but never shown





















































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown

































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown







                      Popular posts from this blog

                      Wiesbaden

                      Marschland

                      Dieringhausen