Ytukyg

Hi I am trying to draw the following circuit:

using Tikz package in Latex. The following is my code

begin{figure}[t]

    begin{center}

        ctikzset{bipoles/length=1cm}

        begin{circuitikz}[scale=1,transform shape]

            draw

            %(0,1) node  {} to [R, l=$R_t$, i>^=$I_t$] (2,1)

            (0,1) to [cspst=$u$] (1.5,1)

            (0,-1) node  {} -- (6,-1)

            (0,-1) {to [battery, l_=$V_s$] (0,1)}

            (1.5,1) to [L, l=$L_1$, i>^=$I_1$] (1.5,-1)

            (1.5,1) to [C, l=$C_1$, v<={{$V_1$}}] (3.5,1)

            (3.5,1) {to [diode] (3.5,-1)}

            (3.5,1) to [L, l=$L_2$, i>^=$I_2$] (5,1)

            (5,1) to [C, l=$C_2$, v<={{$V_2$}}] (5,-1)

            (6,-1) {to [R, l_=$G$] (6,1)}

            (5,1) -- (6,1);

        end{circuitikz}

    end{center}

    caption{Electrical scheme of the zetaconverter.}

    label{fig:zeta_scheme}

end{figure}

This always results in the following:

It always invert the sign conversion and the battery too. If I compile in my friend's Mac it becomes normal.

PS: These are my packages and some custom commands:

usepackage{tikz}



usetikzlibrary{arrows,automata}

usetikzlibrary{shapes,backgrounds,calc,positioning,patterns}

usepackage{balance} 

usetikzlibrary{decorations.pathmorphing,decorations.markings,mindmap,trees}



tikzstyle{block} = [draw, rectangle, minimum height=2em, minimum width=4em]

tikzstyle{sum} = [draw, fill=blue!20, circle, node distance=1cm]

tikzstyle{input} = [coordinate]

tikzstyle{output} = [coordinate]

tikzstyle{pinstyle} = [pin edge={to-,thin,black}]



usepackage{blox}

usepackage{cases}

usepackage{framed}

colorlet{shadecolor}{black!15}

usepackage{bigints}



usepackage[american,cute inductors,smartlabels]{circuitikz}



ctikzset{bipoles/thickness=1}

ctikzset{bipoles/length=0.8cm}

ctikzset{bipoles/diode/height=.375}

ctikzset{bipoles/diode/width=.3}

ctikzset{tripoles/thyristor/height=.8}

ctikzset{tripoles/thyristor/width=1}

ctikzset{bipoles/vsourceam/height/.initial=.7}

ctikzset{bipoles/vsourceam/width/.initial=.7}



tikzstyle{every node}=[font=small]

tikzstyle{every path}=[line width=0.8pt,line cap=round,line join=round]

It should because of the difference is version of circuitikz used. Quoting from Circuitikz manual:

Since v0.8.2: voltage and current label directions(v<= / i<=) do NOT
change the orientation of the drawn source shape anymore. Use the
”invert” option to rotate the shape of the source. Furthermore, from
this version on, the current label(i=) at current sources can be used
independent of the regular label(l=).